New Construction
Bathroom Electrical Wiring
GFCI circuits, vanity lighting, exhaust, and heated floors.
What the job involves
GFCI circuits, vanity lighting, exhaust, and heated floors. Half of these calls turn out to be a different problem than the one that got reported, which is why we test before we quote.
Most of this is sequencing. Do it out of order and you pay for it twice. Materials matter here. The commodity version of this part is where most of the callbacks in this trade come from.
How we handle it
- Plan reviewed and load calculated before rough in
- Rough in coordinated with the other trades
- Inspections staged so nothing waits on us
- Trim finished and every circuit tested at completion
Doing this in the White Mountains
Half the calls up here start with a homeowner who has already replaced the breaker twice.
Elevation, weather, and the age of the housing stock all change how this work goes here compared with a valley city. Equipment ages faster in this sun, monsoon surge is a real load on the system, and a lot of these houses were built as seasonal property and are now carrying full-time demand.
You get a firm price before the work starts, and the person who quoted it is the person doing it.
Planning for what you will want later
Nearly every house eventually wants something it was not built for: a charger, a shop, a hot tub, a heat pump, an office that needs real circuits.
Panel space is the cheapest thing to overprovide at build time. So is conduit to places that are hard to reach later, like a detached garage or an attic.
The load calculation should reflect where the house is going, not only where it starts. That is a conversation worth having during design rather than during a remodel.
A load calculation for a house nobody lives in yet
Calculating load for a house that does not exist means working from the plans and the specifications rather than from measured usage, which sounds like guesswork and is not. The code method totals square footage, fixed appliances, and the specific large loads, then applies demand factors.
The part that takes judgment is the equipment that has not been chosen yet. A kitchen with an induction range calculates differently from the same kitchen with gas. A garage that will hold two electric vehicles in five years is a different house from one that will not.
So the conversation during design is about intent rather than model numbers. Tell us what the house is meant to become, and the service gets sized for that rather than for the day the keys change hands.
The order inspections happen in
A build has a sequence and electrical sits at a specific point in it. Rough-in goes in after the framing is complete and the roof is on, after the plumbing and mechanical have claimed their routes, and before insulation and drywall.
The rough inspection has to be passed before anything covers the work. That sounds obvious and it is the most expensive rule on a job site to break, because the remedy is opening finished wall to show an inspector something that was correct all along.
Final inspection comes after devices, fixtures, and the panel are complete and the service is energized. Between those two the wiring sits untouched inside the walls, which is why the quality of the rough-in decides the quality of the house.
What you get
- LicensedC-11 #192532 and R-11 #192533
- PriceFirm, before the work starts
- Who shows upThe person who quoted it
- PermitsHandled where the job needs them
- AfterLabeled, documented, and cleaned up
A firm price before the work starts, from the person who is going to do the work.
The order inspections happen in
A build has a sequence and electrical sits at a specific point in it. Rough-in goes in after the framing is complete and the roof is on, after the plumbing and mechanical have claimed their routes, and before insulation and drywall.
The rough inspection has to be passed before anything covers the work. That sounds obvious and it is the most expensive rule on a job site to break, because the remedy is opening finished wall to show an inspector something that was correct all along.
Final inspection comes after devices, fixtures, and the panel are complete and the service is energized. Between those two the wiring sits untouched inside the walls, which is why the quality of the rough-in decides the quality of the house.
Coordinating with the other trades
Electrical rough-in sits between framing and drywall, sharing the wall cavities with plumbing and mechanical. Whoever arrives last finds the good routes taken.
Good coordination means knowing where the ductwork and the drain stacks are going before drilling, and it means not notching structure that the framer needs.
We plan around the other trades rather than through them, which is slower on the day and considerably faster across the project.
Questions we get
Can we live in the house during a rewire?
Usually yes. We sequence it so the house keeps power throughout, working through it a section at a time.
Do you have to open all my walls?
No. We fish where the framing allows and open only where there is no route. Minimizing patching is most of the skill in a rewire.
Does new wiring need an inspection?
Yes, and it gets staged so the rough in is signed off before anything is closed up.
Are you licensed?
Yes. We hold a C-11 commercial license, number 192532, and an R-11 residential license, number 192533. Both are current and we are insured.
Can you come out after hours?
For genuine emergencies, yes. Burning smells, sparking equipment, water in electrical gear, or a hot panel are not next-week problems.
Towns we cover
Based in Pinetop-Lakeside, covering about forty miles out across Navajo County and the western side of Apache County.
- Show LowOur second base. Panel work and service upgrades on the newer builds off Deuce of Clubs.
- Pinetop-LakesideHome ground. Cabin rewires, fixture work at cathedral-ceiling height, and same-week calls.
- SnowflakeLonger runs out to property on acreage, where the well pump and the house share one panel.
- TaylorOlder service entrances that predate the current code, and the corrections that go with them.
- Heber-OvergaardHeavy second-home territory. Freeze-season calls on places that sat empty since fall.
- LindenBetween Show Low and Pinetop. Remodel wiring and additions on established lots.
- GreerHighest elevation we cover. Generator and backup work for a road that closes in weather.
- ConchoWide-open lots on the Apache County side, often with a long feed from the meter to the house.
- OvergaardPonderosa country. Fixture and circuit work in cabins built across four decades.
- LakesideOlder lakefront cabins where the original wiring was never meant for today’s load.
- PinetopThe cabin core. Small jobs, one outlet or one switch, are most of what we do here.
- White Mountain LakeSeasonal places that need a look before the family arrives and after they leave.
Get it handled
Call (928) 358-2546 or send a message and we will work out what the job actually is.
See recent work or send the details and we will come look.